For use on all above lift cylinders on GFF, GBT, CFF, CBT, & CTL-60 Series Lifts, and AMS-20 Mobile Workstation bottom stage.

Note: See A-491-250 seal removal tool and A-491-251 spanner wrench to make seal kit replacement easy on above ground lifts.
A-491-250 removal tool not required on CTL-60 and AMS-20.

For use on the following:

Lift Models: A-12C30, A-12D30, A-12E30, A-12M30, A-12M50, A-12030, A-12130, A-1CJ30, A-5CM30, and A-6CM30.

Note: This Seal Kit (K34115) is also good if the Model Numbers end in “0” thru “9”. If the Model Number ends with a letter “A” thru “Z”, use Seal Kit K34300 (8-1/2" Dia. Plunger).

Cylinder Assembly: T08971, T09205, T11934, T11936, T11937, T11896, and T11984.

Note: This Seal Kit (K34115) is also good for any of the numbers above that end with a dash number, such as T08971-01.

Use Seal Insertion Tool Kit K34138.

For use on the following:

Lift Models: A-12D3A, A-12E3A, A-12M3A, A-12M5A, A-12N3A, A-12J3A, A-5CM3A, and A-6CM3A.

Note: This Seal Kit (K34300) is also good if the Model Numbers end in “A” thru “Z”. If the Model Number ends with a letter “0” thru “9”, use Seal Kit K34115 (7-1/2" Dia. Plunger).

Cylinder Assembly: T13916, T13921, and T13922.

Note: This Seal Kit (K34300) is also good for any of the numbers above that end with a dash number, such as T13922-01.

Use Seal Insertion Tool Kit K34153.

For use on the following:

Lift Models:

A-1AA10, A-1AA30, A-1AB10, A-1AB30, A-1A030, A-1AP10, A-1AP30, A-1AR10, A-1AR30, A-1AV10, A-1AV30, A-1A110, A-1A130, A-1A210, A-1A230, A-1CJ30, A-2BF30, A-2BG30, A-2BM30, A-3BM50, A-3FM50, A-3FT50, A-3GT50, A-5CM30, A-6CM50, A-8BM60, A-8FT60, A-9BM60, 12 & 13, 14 & 15, 18-00, 18-01, 18-20, 18-21, 18-30, 18-40, 18-41C, 19-00, 19-01, 19-20, 19-21, 19-30, 19-40, 20-30, 20-40, 30-30, 30-40, 31-30, 31-40, 40-30, 40-40, 41-40, 78-40, 79-40, FCF 2, 4, & 6, and
FCS 3, 5, & 7

Note: This Seal Kit (K34113) is also good if the Model Numbers end in “0” thru “9”. If the Model Number ends with a letter “A” thru “Z”, use Seal Kit K34301.

Cylinder Assembly:

TO5141, TO5238, TO5351, TO5352, TO5360, TO6144, TO6177, TO6876, TO7783, TO7909, TO7999, TO8287, TO8354, TO8360, TO8563, TO8612, TO9408, TO9494, TO9507, TO9508, T11918, T11997, T13124, T13126, W01697, and W01699.

Note: This Seal Kit (K34113) is also good for any of the numbers above that end with a dash number, such as T08354-01.

Use Seal Insertion Tool Kit K34118.

For use on the following:

Lift Models:

A-1AA1, A1AA3A, A-1AB1A, A-1AB3A, A-1A11A, A-1A13A, A-1AN1A, A-1AN3A, A-2BJ3A, A-BM3A, A-3BM5A, A-5CM3A, A-6CM5A, and A-3FM5A.

Note: This Seal Kit (K34301) is also good if the Model Numbers end in “A” thru “Z”. If the Model Number ends with a letter “0” thru “9”, use Seal Kit K34113.

Cylinder Assembly:

T13944, T13945, T13946, T13952, T13959, and T14000.

Note: This Seal Kit (K34301) is also good for any of the numbers above that end with a dash number, such as T13944-01.

Seal Insertion Tool Kit Not Required.

For use on Models 12D & 12L with hydraulic cylinders 89-3/4" on center.

For use on Models 12E & 12N with hydraulic cylinders 57-1/2" on center.

Used to convert alignment lift to single post swing rail drive-over lift.

Kit contains (4) swing arms, crosshead, slide bases, pick-up pads, and fasteners.

Note:
Capacity: 8,000 lb.
2,000 lb./swing arm.

Used to convert two post side by side alignment lift to drive thru swing rail lift. For lifts with cylinder assemblies 57 1/2" on center.

Kit includes (4) swing arms, (2) anchor plates, slide bases, pick-up pads, and fasteners.

Note:
Capacity: 4,000 lb./side.
2,000 lb./swing arm.

For use on Model 12DCode No.


Note: Swing Arms Not Included. Drilling Existing Arms Required.

Note:
Capacity: 8,000 LB.
2,000 LB./Swing Arm

For use on Model A-3FM5A Series Lifts.

Kit includes entire rear replacement with dual
10 5/8" dia. full hydraulic cylinders.

Non-EnviroKote coated dual cylinder assembly.

Note:
36,000 lb. capacity

For use on Model A-3FM5A Series Lifts.

Kit includes entire rear replacement with dual
10 5/8" dia. full hydraulic cylinders.

EnviroKote coated dual cylinder assembly.

Note:
36,000 lb. capacity

For use on Model A-3FM5A Series Lifts.

Kit includes entire rear replacement with dual
10 5/8" dia. full hydraulic cylinders.

Non-EnviroKote coated dual cylinder assembly.

Note:
36,000 lb. capacity

For use on Model A-3FM5A Series Lifts.

Kit includes entire rear replacement with dual
10 5/8" dia. full hydraulic cylinders.

EnviroKote coated dual cylinder assembly.

Note:
36,000 lb. capacity

For use on Models: 2BM, 3BM, 5CM, and 6CM.

Kit includes entire rear replacement with 10 5/8" dia. full hydrulic cylinder. Non-EnviroKote coated cylinder assembly.

Note:
18,000 lb. capacity.

For use on Models: 2BM, 3BM, 5CM, and 6CM.

Kit includes entire rear replacement with 10 5/8" dia. full hydrulic cylinder. EnviroKote coated cylinder assembly.

Note:
18,000 lb. capacity.

This kit used to convert old style 2BM and 3BM with floating bearings at front to new style
2-BM3A and 3-BM5A with
replaceable upper bearing only. Non-EnviroKote coated cylinder assembly.

Kit includes all fasteners, forward pick-up base, cylinder assembly, complete lock leg assembly, carriage assembly, and (2) trench covers adjacent to cylinder.

Kit Requirements:
Existing Track Width: 17-13/16"
Existing Pit Depth: 94" (From finished floor to bottom of pit)

Note:
18,000 lb. capacity.

For use on models: 12M3 and 12M5.

Kit includes entire rear replacement with 8-1/2" dia. full hydrulic cylinder. Non-EnviroKote coated cylinder assembly.

For use on models: 12M3 and 12M5.

Kit includes entire rear replacement with 8-1/2" dia. full hydrulic cylinder. EnviroKote coated cylinder assembly.

This kit used to convert old style 12M3, 12M5, 5CM, and 6CM with 7-1/2" plunger/cylinder assemblies to 8-1/2" plunger/cylinder assemblies with replaceable upper bearing only. Non-EnviroKote coated cylinder assembly. Kit includes all fasteners, forward pick-up base, cylinder assembly, complete lock leg assembly, carriage assembly, and (2) trench covers adjacent to cylinder.

Kit Requirements:
Existing Track Width: 14-3/4"
Existing Pit Depth: 92" (From finished floor to bottom of pit)

Note:
18,000 lb. capacity.

This kit is used to replace 2BM and 3BM complete front plunger/cylinder assemblies. This kit is also used to convert old style 2BM and 3BM with floating bearings at front to new style 2-BM3A and 3-BM5A with replaceable upper bearing only. Non-EnviroKote coated cylinder assembly. Kit includes all fasteners, forward pick-up base, cylinder assembly, complete lock leg assembly, carriage assembly, and (2) trench covers adjacent to cylinder.

Kit Requirements:
Existing Track Width: 17-13/16"
Existing Pit Depth: 94" (From finished floor to bottom of pit)

Note:
18,000 lb. capacity.

For use on models: 5CM, 6CM, 2BM, and 3BM.

Kit includes entire rear replacement with 10 5/8" dia. full hydrulic cylinder. EnviroKote coated cylinder assembly.

For use on models: 5CM, 6CM, 2BM, and 3BM.

Kit includes entire rear replacement with 10 5/8" dia. full hydrulic cylinder. Non-EnviroKote coated cylinder assembly.

(Remote Lock)For Use On Models: 3BM5, 4BM6, 3FM5, and 7FM6.

Kit includes the entirely redesigned control box. New box comes with easy maintainence features and quieter operation.

For Use On Models: 3BM5 and 3FM5.

Kit includes the entirely redesigned control box. New box comes with easy maintainence features and quieter operation.

A Lower Cost Alternative To Globe's C34354 Pad & Adapter!

MANITOWOC LIFT's four-position flip-pad adapter & sleeve assemby (N20366-01) is interchangable with the C34354 adapter on Globe's frame contact lifts that utilize a 1-1/2" X 6" steel arm.

AND WE PROVIDE THEM AT ABOUT 35% LESS COST!!!

Call our Tech Support line for more details and ordering information, 1-800-783-5777.